It is very easy to rekey a Schlage lock. Follow the below-mentioned instructions on how to rekey a Schlage lock.
Instructions For Rekeying A Deadbolt
Whenever you are stuck in a situation where rekeying a deadbolt of the Schlage lock is the only solution, make sure to follow the following steps. However, if you are not comfortable, you can seek professional help by searching Rekey lock in Schiller Park.
- Firstly, remove the deadbolt from the packaging and replace the original key.
- Secondly, To remove the cylinder cap, use a cylinder cap removal tool.
- Thirdly, Take off the cylinder pin.
- After that, Take out the spring from beneath the cylinder pin.
- Turn the key to the 2 o’clock position.
- Moving forward, Slide the deadbolt casing away from the cylinder using a follower bar. Remove the follower bar at your own risk.
- Remove the existing bottom pins from the cylinder. Take out the original key.
- Moreover, Find the key cut number on the replacement key. Insert a new key into the cylinder.
Hint:
If a key number cannot be found or rekeying from a duplicate key, use a key gauge to establish the proper pin height.
- Additionally, Examine the rekey kit map for pin placements and numbers to new keys.
- Insert the correct numbered pin into the first hole, reading the cylinder from right to left. (While the cylinder is removed, the follower bar must stay in the housing, and the notch in the follower bar must be horizontal.) Therefore, Insert the pin with the correct number into the second hole.
- Now, Insert the appropriate numbered pins into the third, fourth, and fifth holes.
- Most importantly, Check that all inserted pins are flush with the top of the cylinder. (With the new key in place, ensure that all pins are flat with the top of the plug, making a perfect shear line. If any extend above or below the surface, replace with the appropriate sizes.)
- Using the follower bar, push the cylinder back into the deadbolt housing. Take out the key.
- Replace the cylinder spring.
- Replace the cylinder pin.
- Finally, Tighten the cylinder cap back onto the cylinder using a cylinder cap removal tool.
- Lastly, To ensure rekeying success, simulate locking and unlocking the deadbolt.
Keypad Lock Rekeying Instructions
Many Schlage locks come with a keypad. The Keypad lock is a little bit technical but however, we have simplified the instructions for you. However, you can also contact Rekey Lock in Melrose Park for professional assistance.
- Firstly, Remove the inside of the keypad lock from its packing.
- Secondly, Remove the packaging’s support parts.
- Thirdly, Open the built-in door on the keypad lock’s exterior.
- Now, To remove the cylinder cap, use a cylinder cap removal tool.
- Take off the cylinder pin.
- Take out the spring from beneath the cylinder pin.
- Insert the original key and turn it clockwise to the two o’clock position.
- Slide the keypad lock casing away from the cylinder using a follower bar. ! (The follower bar must remain in the housing when the cylinder is removed and the horizontal notch in the follower bar is removed.)
- Remove the existing pins from the cylinder. Take out the original key.
- Find the key cut number on the replacement key. Replace the key in the cylinder. (If a key number cannot be found or rekeying from a duplicate key, use a key gauge to establish the proper pin height.)
- Examine the rekey kit map for pin positions and numbers corresponding to the new Schlage key.
- Insert the correct numbered pin into the first hole, reading the cylinder from right to left. Moreover, keep in mind that Key numbers are read from left to right.
- Insert the appropriate numbered pin into the second hole.
- Insert the appropriate numbered pins into the third, fourth, and fifth holes.
Tip:
Check that all inserted pins are flush with the top of the cylinder. (With the new key in place, ensure that all pins are flat with the top of the plug, making a perfect shear line. However, If any extend above or below the surface, replace with the appropriate sizes.)
- Moving further, Push the cylinder back into the keypad lock housing using the follower bar and take out the key.
- Replace the cylinder spring.
- Replace the cylinder pin.
- Tighten the cylinder cap back onto the cylinder using a cylinder cap removal tool.
- Lastly, Replace the built-in door with the lock assembly.
- Most importantly, To validate rekeying success, simulate locking and unlocking the keypad lock.
Instructions For lever rekeying:
- Firstly, Unlock the lever and leave the key in the cylinder.
- Secondly, To remove the lever from the chassis, use a key gauge.
- Thirdly, Disconnect the lever from the chassis.
- Remove the key from the cylinder and push it out of the lever.
- Remove the cylinder’s C clasp (by twisting like you are peeling an apple).
- Slide the cylinder housing away from the cylinder using a follower bar. Remove the follower bar at your own risk. (While the cylinder is removed, the follower bar must stay in the housing.)
- Moreover, Remove the existing pins from the cylinder. Remove the original key.
- Find the key cut number on the replacement key. Replace the key in the cylinder. (If a key number cannot be found or rekeying from a duplicate key, use a key gauge to establish the proper pin height.)
- Now, Examine the rekey kit map for pin placements and numbers to new keys.
- Insert the correct numbered pin into the first hole, reading the cylinder from right to left.
- In the second hole, insert the correct numbered pin.
- Insert the appropriate numbered pins into the third, fourth, and fifth holes.
- After that, Check that all inserted pins are flush with the top of the cylinder.
- Slide the cylinder housing back over the cylinder from the follower bar.
- Replace the C clip on the cylinder. Take out the key.
- Replace the whole cylinder assembly with the lever component.
- Return the lever component with the cylinder to the chassis. (Hint: If done correctly, you will hear a clicking sound or feel the tab click into place.)
- Lastly, Insert a new key and turn until the lever component is locked in place.
- Most importantly, To ensure rekeying success, simulate locking and unlocking the product.
Conclusion:
In conclusion, we can say that rekeying a Schlage lock is easy. Firstly, these locks are quite handy. Secondly, they do not require high maintenance. Therefore, you can rekey a lock at home without being tired.
Also read: Why Choose Aluminium Doors & Windows? Top Reasons